分類:公司新聞發布時間:2015/01/10
一、動力控制系統 三民重科小型混凝土泵采用380V、50Hz三相交流電源,采用了星一三角啟動, 混凝土泵電源接通后,首次使用時應檢查電機的轉向與電機標明的轉向是否一致,若轉向不一致,必須馬上停機,調查轉換向后,方可新啟動。 警告:主回路未采用隔離接觸器,當電控箱內空氣開關合上時,主電機線端仍有危險的電壓存在。英雌,當電控箱內空氣開關QS接通后,禁止打開控制器和主電機的接觸接線盒檢修。如果在進行故障排除,測量等工作時,部分電路必須帶電的話,只能由專業維修人員,嚴格按照有關安全條例采區適當的方法來進行。
二、電控箱控制系統 主電機啟動和停止均在電控箱上操作。將“控制遙控”轉換開關旋到“控制”位置,泵送進入電控箱操作狀態。 1、泵送啟動及停止 為保證主電機正常運轉,防止帶載啟動,自動泵送只有在主電機啟動完畢后才能啟動。主電機不啟動或在啟動工程中,按電控箱面板上SB4泵送啟動按鈕無效。 按泵送停止按鈕SB3,泵送停止并為分配閥點動及主缸點動作好準備。 2,手動反泵 當需要反泵工作時,旋轉二位選擇開關SB10,即可實現反泵動作。要停止反泵只需將SB10復位即可。 3,主缸點動 當自動泵送停止時,旋轉SB10按鈕,關保持在點動位置,即可實現主缸點動;松開旋轉鈕自動復位,停止啟動。
三、有線遙控系統 當需要采用遙控操作時,必須將電控箱面板上“”控制遙按“旋轉SB9置于遙控位置,并把遙控器上的電纜插頭與箱體上相應插座連好關鎖緊。在遙控盒上設有泵送啟動、泵送停止、正反泵防水開關,其控制功能與電控箱相應按鈕開關相同。